Summer Breeze Maxi Dress Mini Tutorial

Introducing the Summer Breeze Maxi Dress...

 I purchased a thrifted flat sheet a couple months ago thinking I would eventually use it as a muslin or for a spring bag.  I didn't get around to the bag so I went with the muslin!

I actually REALLY like the fabric now that the dress is complete.  It was one of those sheets that was incredibly soft, cool to the touch, and breezy.  I just wanted to hold it to my cheek and go to bed!

Materials:

1 flat sheet

1 yd 1/4" elastic

1 yd 1/2" elastic

matching thread

Here are the pattern pieces I started with.

The rectangle on the bottom right was one of two.  So, 2 body pieces, 4 sleeves and 2 ruffles. 

To get your body piece pattern, measure your bust.  For me, 36 1/2" divided by 4.  So my bust # is 9 1/4". Measure your hips.  For me, 34 1/2" divided by 4.  My hips # is 8 3/4".  

Measure your overbust to underbust (x), then underbust to hip (y).

Fold your fabric in half.  Then cut your pattern based on this guideline.

 

source

To achieve the pattern for my sleeve, I used 18" length, 4 1/2" wide at the short ends and 6 1/2" wide at the widest part (the curve).  Cut a rectangle that is 18" x 6 1/2".  Mark at the 4 1/2" mark on the short side and fold in half.  Begin cutting a curve at this mark, ending the curve at the fold.

My ruffle pieces were 13" wide by twice the measurement of the bottom hemline measurement.  So, if your front hemline is 35", then the ruffle is 70" long. 

Pin body pieces together and sew down each side.  Set aside.

Sew a basting stitch along the top of each ruffle piece.  Adjust the ruffle to be the same width as your hemline of the dress.  With right sides together, sew down each side seam creating a large tube.  Match up the seams in the ruffle to the seams in the dress with right sides together.  Pin together and sew with a 1/2" seam allowance.  Press this seam up.  Top stitch along the top of this seam.  (the part that is NOT ruffled) 

Up close :)

Sleeves

Using 2 sleeve pieces, pin right sides together and sew down the long straight edge and the curved edge.  Leave short ends open.  Repeat with second two sleeve pieces.  Turn right side out.  Press.  Topstitch down the same two seams.  Cut 2 three inch pieces of 1/4" elastic.  Fold the sleeve in half, wrong sides together and press.  Measure up from the fold 3" along the curved edge.  Place the end of the elastic here, place under pressure foot and slide needle down into the elastic/fabric.  Stretch the elastic out and sew in place using a zigzag stitch.  Repeat this step with second sleeve. 

Casing and Empire Waste

Take the body of the dress and turn inside out.  Fold down 1/4" along the top of the chest, then another 3/4" creating a casing.  Sew in place along the edge and be sure to leave a couple inches open for feeding the elastic through.  Using 1/2" elastic, wrap a long piece around your upper bust.  Stretch it around the upper bust until it feels comfortable.  For me, about 30".  Feed elastic through the casing using a safety pin.  Once elastic is fed all the way through, overlap the ends about 1/2" and sew in place.  Make sure the elastic is NOT twisted inside of casing!!  Sew hole closed.

Measure down from the casing using the measurement you got from the upper bust to the lower bust.  Using a fabric pencil, draw a line all the way around the dress at this measurement.  Wrap a 1/4" piece of elastic around your underbust and determine how long you want the elastic to be.  Place the end of the elastic at a side seam and set pressure foot on top, with needle down.  Stretch that elastic as you sew it down, all the way around the garment, using a zigzag stitch as you did with the sleeves.  Try on the dress.

At this point, I tried on my dress and the empire waste hung too low.  The back was too poofy.  So, I ended up cutting that casing out to make the bust piece shorter.  The front was great but the back was still too poofy.  So, to correct the back, I began cutting the fabric under one arm, curving downward at the back and coming back up at the other underarm.  I basically cut off about 2 1/2" of fabric to lose that poofiness in the back.  The curving at the underarms was because I didn't want to lose that fabric in the bust area.  I also took in the sides as that was looking alot a bit boxy. 

Grab a friend or a hubby for this step.

Attach those sleeves!!  Pin them where you want them then sew them under the casing (following the casing seam) and above the casing.  This was difficult and time consuming for me because I only had myself.  I had to try it on 3-4 times before I had it right. 

Hem that dress!!!

WHEW!!  If you have any questions, please let me know!  This is my first clothing tutorial and I don't have progression photos because I didn't really know what I was doing!!  If there is a next time, I'll take photos.  For now, you'll have to settle for lots of words and lots of finished product photos. 

So tell me, would you wear this??